Flint-walling CPJS Shallow Well Bedienungsanleitung

®Installation Instructions and Parts Manual “CPJ” SERIES JET PUMPSConvertible Jet Pumps1/2 HP “CPJ” CONVERTIBLE3/4 - 1-1/2 HP “CPJ” CONVERTIBLE1/3 - 1

10WELL TO PUMP CONNECTION (SUCTION PIPE)4b. For driven wells, a check valve is required at the top of the well to maintain prime. Flow arrow must poi

11PUMP TO PRESSURE TANK CONNECTION (DISCHARGE PIPE)Shallow Well Application Only:1. Begin the connection to the pressure tank. Using a 3/4 in. x 3 in

12PUMP TO PRESSURE TANK CONNECTION (DISCHARGE PIPE)Deep Well Application Only:1. To begin the connection to the pressure tank, loosely assemble ow c

13TANK TO HOUSE CONNECTION1. Most pressure tanks will have a 1 inch inlet elbow on the bottom. Connect to this elbow with a 1 in. MPT x 1 in. slip (

144. Install a 3/4 in. union (optional) and continue with pipe and 3/4 in. x 3/4 in. x 3/4 in. tee. (Fig. 4)3. Attach a 1 in. slip (glue) x 3/4 in.

15PUMP ELECTRICAL CONNECTIONSIL14012L1L2ABL1L2AB115 VoltsSingle PhaseLine230 VoltsSingle PhaseLineYELLOWWHITEGREYREDTANYELLOWWHITEGREYREDTANCheck Volt

16PUMP ELECTRICAL CONNECTIONS3. Insert an electrical wire strain relief into the opening in the side of the pressure switch closest to the motor. (Fi

177. Insert an electrical wire strain relief into the opening in the opposite side of the pressure switch. (Fig. 7)IL1376Wire from motorPressureSwitc

18PUMP ELECTRICAL CONNECTIONSTo change from 115V to 230V11. The motor of this pump is dual voltage and can run on either 115V or 230V. In general, 23

19PUMP PRIMING & STARTUPShallow Well Application Only: CAUTION: All pumps must be primed (lling the cavity with water) before they are rst ope

2PRODUCT SPECIFICATIONS SAFETY INFORMATION DANGER: 1. Always disconnect power source before performing any work on or near the motor or its connec

20PUMP PRIMING & STARTUP Deep Well Application Only: CAUTION: All pumps must be primed (lling the cavity with water) before they are rst opera

21PUMP PRIMING & STARTUP 5. With pump operating at high pressure, open two or more faucets and slowly unscrew the ow control screw until maximu

22Rotary Seal Assembly Replacement CAUTION: Make certain that the power supply is disconnected before attempting to service the unit! The rotary se

23TROUBLESHOOTINGProblem Possible Cause Corrective ActionLittle or no discharge1. Casing not initially lled with water 1. Fill pump casing2. Sucti

24REPAIR PARTSIL0190IL0189IL01913124567810111291315IL018813141616“CPJ” Convertible3/4 to 1-1/2 HP“CPJS” Shallow Well1/3 to 1/2 HP“CPJS” Shallow Well3/

3Typical Pump SetupConvertible jet pumps are designed for use in these applications:1. Shallow wells (0 - 25 ft. lift) where ejector bolts to pump (Fi

4GENERAL PUMP INFORMATIONIL02093/4 or 1 in. Discharge PipeSuctionPipe SeeTable BDischarge to Home Pipe SupportFoot Valve2 in. ID Well33. Deep wells w

5VentilationVentilation and drainage must be provided to prevent damage to the motor from heat and moisture.FreezingThe pump and all piping must be pr

6Tools requiredPREPARATIONPipe wrenches (2)Wire strippersNeedle-nose pliersPhillips screwdriverWire cuttersAdjustable wrenchPipe tapePipe dopeNOTE: Fo

7INSTALLING PIPING IN WELL IL11883/4 or 1 in. Discharge Pipe1-1/4 in.SuctionPipeDischarge to Home CheckValve2RECOMMENDED SUCTION PIPE SIZES FOR SHALLO

8Deep Well (Single Pipe System)Application - Where pumping water level is greater than 25 feet and inside diameter of well is 2, 2-1/2 or 3 inches. (F

9WELL TO PUMP CONNECTION (SUCTION PIPE)IL1392Glue33. The use of a union (optional) will assist with easy connection and disconnect. (Fig. 3)IL1346G